Customization: | Available |
---|---|
Main Composition: | Coating Gun, Coating Room, Powder Recycling System |
Type: | Electrostatic Spraying Equipment |
Suppliers with verified business licenses
Audited by an independent third-party inspection agency
Filters (easy assembly and dismantle) |
Recyling powder collection mode (selection) |
powder sucking pump (strong sucking force) |
Input voltage | Input power | Work voltage | Output voltage | Hi-pot installation mode |
AC220V,50Hz +/-10% |
40W | DC24V | 0-24V | Built in |
Max electro-static output voltage | Max output current | Power cable | Output Hi-pot | Powder coating gun weight |
0-100KV (adjustable) |
100UA | About 4 meters | 0-100KV negative | About 425g |
Trouble | Possible reason | Solution |
Color difference | 1.oven temperature is much high or much low. 2.curing time too long or too short. 3.inadequate exhaust in the oven |
1.adjut the oven temperature 2.adjust the chain speed or curing time 3.check exhaust system or increase the exhaust holes. |
Orange peel grain | 1.coating layer is too thin or too thick. 2.oven temperature rising speed is too fast or too slow. 3.curing temperature is much low. 4.the powder is expired. 5.powder atomization is not good. |
1.adjust the gun parameter or the chain speed 2.check and adjust the oven. 3.adjust the oven curing temperature. 4.replace the powder or contact the powder supplier. 5.adjust the powder atomization. |
Shrink hole | 1.it is not compatible with other suppliers' powder. 2.inadequte pre-treatment with the part. 3.it was contaminated by the incompatible substance. 4.any oil or over water contained in the compressed air. |
1.clean the coating system absolutely. 2.check the pre-treatment 3.check any incompatible substance in the coating area. 4.check the air source and install the filter. |
Pin hole | 1.coating thickness is much 2.the part with water 3.coating voltage is too high 4.gun distance is much close 5.the powder got moisture |
1.reduce the coating thickness. 2.preheating the part 3.reduce the gun voltage 4.adjust the gun distance 5.contact the powder supplier. |
Bad absorption | 1.inadequate pre-treatment 2.inadequate coating layer curing 3.coating is too thick 4.part change |
1.check the pre-treatment equipment and pre-treatment liquid. 2.check the oven temperature, extend the curing time. 3.adjust the coating parameter and reduce the coating thickness 4.contact the part supplier. |
Bad coating in the groove | 1.inadequate pre-treatment before coating 2.coating mist is too wide 3.the part grounding connection is not good 4.coating voltage is too much high 5.gun distance is too big 6.powder feeding pressure is too small or too big 7.the powder is too thin |
1.adjust the gun angle to let the powder against the groove directly. 2.use small choke nozzle or contact the gun supplier. 3.check the hanging device and grounding cable. 4.reduce the coating voltage 5.shorten the gun distance 6.adjust the powder feeding pressure. 7.reduce the recycling powder ratio. |
Bad coating rate | 1.inappropriate part grounding connection 2.inappropriate gun voltage 3.powder got moisture 4.fill in too much recycling powder. 5.inappropriate hanging device design 6.gun pressure is too big 7.coating room exhaust is too strong 8.gun electrode got damage 9.powder stays in the electrode |
1. 2.check the gun, clean the gun or replace the gun 3.replace the powder or contact with the powder supplier 4.reduce the recycling powder ratio 5.redesign the hanging device and reduce the shielding 6.reduce the coating pressure 7.reduce the exhaust 8.replace the electrode 9.clean the electrode |
Bad impact or flexibility | 1.inadequate curing with the coating layer 2.bad quality part or pre-treatment 3.coating layer is too much thick 4.the part change 5.checking temperature is too low |
1.check the oven temperature 2.check the part or pre-treatment liquid 3.reduce the coating thickness 4.contact with the part supplier 5.place it for a while >20oC,and then for checking |
Dreg | 1.some dust left in the part 2.recycling powder passes through the sieve 3.the powder coating line is not clean 4.the sieve holes is too big for the recycling powder. 5.any dreg in the supplying powder. |
1.do the pre-treatment carefully with the part 2.sieve the recycling powder. 3.clear the powder room, recycling device, transporting line and hanging device. 4.replace the smaller holes sieve for the recycling powder. 5.contact with the powder supplier. |
Unevenly powder feeding | 1.venturi wears out 2.powder disperse sleeve wears out 3.powder pump atomizer got jam 4.powder fluidizing is not good 5.the powder got moisture 6.the powder is too thin 7.the powder transporting pipe is too long 8.unstable the compressed air. 9.unstable air pressure 10. the gun distance is too close. |
1.replace the venturi 2.replace the powder disperse sleeve. 3.clean the powder pump 4.check the fluidizing air pressure 5.replace the powder or contact the powder supplier 6.check and adjust the rate of recycling powder against the raw powder. 7.adjust the powder transporting pipe 8.check the compressed air, and install the dryer. 9.chech any overload the compressed air. 10.increase the gun distance. |
Bad fluidizing | 1.the powder is too thin 2.the holes of the multi-holes spoiler in the fluidizing bed is too small 3.the multi-holes spoiler in the fluidizing bed got jam 4.the supplying pressure of the fluidizing bed is too low 5.too much more or too much less powder in the barrel |
1. check and adjust the rate of recycling powder against the raw powder. 2.replace it 3. replace it 4.incrase the powder supply pressure. 5.ensure the powder in the barrel to be 1/3-3/4. |
Impact melting appears in the powder supplying system | 1.much strong powder supply rate 2.the powder particle diameter is not appropriate. 3.much more use the recycling powder 4.compressed air temperature is much high 5.powder transporting pipe got bend 6.the powder transporting pipe material is not appropriate. |
1.reduce the powder supply pressure 2.contact the powder supplier and adjust the powder supply pressure. 3.reduce the recycling powder ratio 4.check the compressed air temperature, and clean any heating source nearby. 5.clear the bending pipe 6.check the powder transporting pipe and replace it if necessary. |
Color change in small area | 1.inadequate pre-treatment 2.some change in the part surface |
1.check the pre-treatment 2.clean it by some chemical. |
Uneven coating | 1.bad powder absorption 2.operator got tired 3.the powder particle diameter is incorrect. 4.the parts of the gun installation is not reliable. 5.chain speed is not suitable 6.powder feeding is unevenly in the gun 7.the gun moving speed is not compatible with the chain speed. 8.the gun distribution is not appropriate. 9.the gun angle/distance is not appropriate. 10. the charging was interrupt |
1.refer above the concerning 2.operator makes the shift working or auto coating. 3.contact the powder supplier. 4.check every part of the gun and ensure reliable installation. 5.adjust the chain speed. 6.refer to above concerning. 7.refer to above concerning. 8.adjust the gun distribution 9.chek the gun distribution 10.adjust the gun and not directly knock against. |
Less powder feeding | 1.input air pressure is too much low. 2.the lining pipe to the powder pump got jam 3.the powder pipe got jam 4.the feeding nozzle of the gun got jam 5.the venturi wears out |
1-5 clean |
Power indicator off | 1.the rear fuse in the main body was burnt. 2.power switch breaks down |
1.replace the fuse 2.replace the power switch |
Powder indicator on but not working | 1.the control cable breaks up 2.the gun switch breaks down |
1.replace the control cable 2.replace the gun switch |
Electro-static induction or hand numb | 1.improper main body grounding wire 2.improper part grounding wire 3.wear the insulated gloves or insulated shoes |
1.correct the grounding wire 2.correct the grounding wire 3.remove the gloves or the shoes. |